sae 1045 mechanical properties Related introduction

  1. ASTM SAE AISI 1045 Carbon Steel Heat Treatment, Chemical ...

  2. MEDIUM TENSILE STEEL AISI 1045 - S&T Stainless

    TYPICAL MECHANICAL PROPERTIES for guidance only Water or oil quenched at 830°C 850°C and tempered between 540°C 680°C. MEDIUM TENSILE STEEL AISI 1045 - continued WELDING: Readily welded as supplied with the correct procedure, but welding when through hardened, flame or induction hardened is not recommended.

  3. 1045 MEDIUM TENSILE CARBON STEEL BAR -

    1045 is a medium tensile low hardenability carbon steel generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 - 700 Mpa and Brinell hardness range 170 - 210 in either

  4. AISI 1045 - Steel grades, Properties and Global Standards

    AISI 1045 can be supplied as steel plate/ sheet, round steel bar, steel tube/pipe, steel stripe, steel billet, steel ingot, steel wire rods. electroslag, forged ring/ block,etc. Join Supplier: [email protected]

  5. AISI 1045 Steel, cold drawn, high temperature stress ...

    AISI 1045 Steel, cold drawn, high temperature stress relieved, 50-75 mm (2-3 in) round. Categories: Metal; Ferrous Metal; Carbon Steel; AISI 1000 Series Steel; Medium Carbon Steel. Material Notes: Respond to heat treatment, and flame and induction hardening,

  6. AISI 1045 Carbon steel plate steel plate,AISI 1045 Carbon ...

    AISI 1045 Carbon steel plate is characterized by good weldability and good machinability.AISI 1045 Carbon steel plate is a medium tensile steel supplied in the black hot rolled or normalized condition. It has a tensile strength of 600 MPa and brinell hardness ranging between 170 and 210.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  7. SAE 1045 Chemical Composition, SAE 1045 Mechanical ...

  8. 1045 MEDIUM TENSILE CARBON STEEL BAR -

    USA AISI C1045 ASTM A29/A29M - 91 1045 SAE 1045 UNS G 10450 Chemical Composition Min. % Max. % Carbon 0.43 0.50 Silicon 0.10 0.35 Manganese 0.60 0.90 Typical Mechanical Properties - Hot Rolled Condition Tensile Strength Mpa 570 - 700 Yield Strength Mpa 300 - 450 Elongation in 50mm % 14

  9. SAE-AISI 1020 Steel vs. SAE-AISI 1045 Steel ::

  10. BAR DATA HANDBOOK AISI/SAE - Steel Dynamics

    means of a mechanical rake. These heats are then treated at the Vacuum Tank Degasser (VTD). Typical gas levels following VTD treatment are 2 ppm H2, 80 ppm N2, and 20 ppm O2. The continuous caster is a three strand, vertical curved radius machine. Each strand is equipped with automatic mould level control and electromagnetic stirring.

  11. AISI 1045 Carbon Steel - AISI 1045 Medium Carbon Steel ...

    General characteristics of Carbon Steel 1045. C1045 is a medium carbon, medium tensile steel supplied as forged or normalized. This steel shows reasonable strength and toughness. C1045 will through harden to 2.5 (63mm) with a tensile strength of 66-120 Ksi (620-850 MPa)

  12. AISI 1045 SAE UNS G10450 Carbon Steel Foundry

    AISI 1045 SAE UNS G10450 Carbon Steel Foundry. Steel foundry in China for producing AISI 1045 SAE UNS G10450 Carbon Steel castings. The followings are this material's chemical composition, physical and mechanical properties and equivalent material grades. The following sections will discuss in detail about AISI 1045 carbon steel.

  13. C45 Round Bar, AISI 1045, DIN 1.1191, JIS S45C - Otai ...

    C45 is a medium strength steel with good machinability and excellent tensile properties. C45 round steel is generally supplied in the black hot rolled or occasionally in the normalised condition, with a typical tensile strength range 570 700 Mpa and Brinell hardness range 170 210 in either condition.

  14. eFunda: Properties of Carbon Steel AISI 1045

    Properties Conditions : T (°C) Treatment: Density (×1000 kg/m 3) 7.7-8.03: 25 : Poisson's Ratio: 0.27-0.30: 25 : Elastic Modulus (GPa) 190-210: 25 : Tensile Strength (Mpa) 585 : 25 : cold drawn, annealed (round bar (16-22 mm)) more: Yield Strength (Mpa) 505 : Elongation (%) 12 : Reduction in Area (%) 45 : Hardness (HB) 170 : 25 : cold drawn, annealed (round bar (19-32 mm)) more

  15. AISI 1045 Carbon Steel (UNS G10450) - AZoM.com

    Jun 17, 2013 · AISI 1045 can be formed into turned, ground and polished bars that can be machined unsymmetrically with limited distortion. The following sections will discuss in detail about AISI 1045 carbon steel. Chemical Composition. The chemical composition of AISI 1045 carbon steel is outlined in the following table.Some results are removed in response to a notice of local law requirement. For more information, please see here.

  16. AISI 1045 Chemical Composition, AISI 1045 Mechanical ...

  17. Mechanical Properties of Steel - Pivot Point

    Mechanical Properties of Steel - Condition, Strength, Hardness, Machinability. Stainless Steels. AISI. Type 302 HQ Type 303. Type 304 Type 316. Type 410 Type 416. Type 17-4 Materials. Condition Annealed Bars. Annealed Bars Annealed Bars. Annealed Bars Annealed Bars. Annealed Bars Bars Cond. A. Cond. H 900 Cond. H 1025. Tensile Strength ksi. 75 - 95 85 - 95 80 - 90 75 - 90. 70 - 100

  18. AISI Steel Mechanical Characteristics - Yield, Tensile ...

    AISI Carbon Steel Mechanical Characteristics - Yield, Tensile, Hardness. AISI 1015 - AISI 1340. Metal Products Distributor Supplier. Metals and Materials Table of Contents. Note: The Table chart below gives typical mechanical characteristics for selected carbon steel properties.

  19. AISI 1045 CARBON STEEL

    AISI 1045 steel is medium tensile steel supplied in the black hot rolled or normalized condition. It has a tensile strength of 570 - 700 MPa and Brinell hardness ranging between 170 and 210. AISI 1045 steel is characterized by good weldability, good machinability, and high strength and impact properties in either the normalized or hot rolled condition.

  20. Properties of 1045 Steel, Sciencing

    Used in the manufacture of a variety of bolts, connecting rods, hydraulic clamps and rams, axles, a variety of pins, a variety of rolls, studs, shafts, spindles and many other metal parts, SAE 1045 steel usually comes in the black hot-rolled variety; however, it also is occasionally manufactured in the normalized condition.

  21. AISI 1045 Steel, cold drawn, high temperature stress ...

    Respond to heat treatment, and flame and induction hardening, but not recommended for carburizing or cyaniding. Die forging and hot upsetting are good to excellent. Typical uses include gears, shafts, axles, bolts, studs, and machine parts. AISI cross reference for JIS S45C and KS SM45C. Key Words:

  22. SAE 1045 Carbon Steel Flat Bar, A29M Bar, ssroundbar

    Available at economical rates, the offered SAE 1045 Carbon Steel Flat Bar are widely used in metallurgical, mechanical, electrical construction field, ships, military uses and automobile rear of products.We are a prominent name in manufacturing and supplying a wide range of SAE 1045 Carbon Steel Flat Bar for our reliable clients.Some results are removed in response to a notice of local law requirement. For more information, please see here.

Online Consultation